How To Print Full Bleed On Allure Photo Panels For Direct Aqueous Printing

You asked and we listened! Now you can print edge to edge on Allure Photo Panels without the need for a shear.

Before, the aqueous metal panels came with a half inch border on all sides to leave room for shearing.

But now, all of the sizes available on the product page will come in our standard sizes.

Printing with Allure Photo Panels is a simple process, and with the help of the new full bleed carrier, it’ll make the process less expensive and even faster.

How To Use The Full Bleed Carrier With Allure Photo Panels

As you can see in the photo above, this is how Allure Photo Panels are now packaged.

Each panel comes preassembled in its own carrier.

To print on Allure, here is what you need:

• Allure Photo Panels
• Epson® printer
• Roller laminator
• Dust Removal System Roller
• X-Acto® knife
• Quartz Laminate Film (Smooth Matte, Luster, or Gloss)

1. Unpackage and Remove the Release Liner

Before you load the sheet into your Epson® printer, make sure you remove the protective release liner on the Allure Photo Panel.

2. Load and Print

Load your Allure panel by first opening the roller release on your Epson® printer.

Next, insert the sheet into your printer with the short edge first.

Keep hold of the panel as you load it into place – the vacuum won’t be strong enough on its own. Select “Sheet Feed” on the printer panel and then press the roller release button to start the load process. Let go of the panel as the printer performs its size and skew checks.

The panel may have shifted slightly once it has finished the size and skew checks. If that happens, simply nudge the panel back into place without releasing the rollers.

Don’t have an Epson® large format printer? You can also print on Allure Photo Panels on desktop Epson® printers!

Here’s the list of printers Allure Photo Panels are compatible with:

• Epson® Stylus Photo Series: R2000, R2400, R2880, R3000
• Epson® Stylus Pro Series: 3800, 3880, 3890, 4800, 4880, 7500, 7600, 7700, 7800, 7880, 7890, 7900, 9500, 9600, 9700, 9800, 9880, 9890, 9900, 10000, 10600, 11880
• Epson® SureColor: P400, P600, P800, P6000, P7000, P8000, P9000, P10000, P20000

Make sure to properly adjust your printer settings before loading and printing on Allure Photo Panels.

3. Laminate the Allure Print With Quartz Laminate Film

Applying Quartz Laminate film to your Allure print helps you to achieve stellar clarity and longevity of Allure.

There’s no need to take off the full bleed carrier for the laminating process.

Just apply Quartz directly onto the full bleed carrier and use that as your bleed space for your lamination.

You will need to use a roll laminator to complete this process. In the photo above, we are using a Drytac JetMounter JM26 Laminator.

Use your Dust Removal System Roller to clean your print before feeding the print into the laminator.

After applying the film onto Allure, feed it through the laminator and your image will be ready to trim!

4. Peel & Trim

Peel the tape from the back of the print before trimming. This helps the trimming process to be a little easier.

Use an X-Acto® knife to carefully trim the laminate from the full bleed carrier.

Feel free to try other cutting tools. We used an X-Acto® knife because of its thin blade and controllable size.

Once your edges and corners are laminate-free, you’re finished!

You’re now finished!

No need to shear. All you need to do is apply hanging hardware, like our Ready to Hang Frames, and sell your metal prints!

Printing With Allure Is Easy And Low-Cost

Do you not have the required materials to start selling metal prints? It’s easy, and relatively low-cost.

You can pump out metal prints with:

• Epson® SureColor P800 from Adorama and get $300 off (~$895)
• Drytac JetMounter JM18 Laminator ($749)

By spending roughly less than $2,000 on a P800, laminator, Quartz Laminate, and Allure Photo Panels, you can start printing and selling metal prints!